Stainless steel sandwich pot use and characteristics 1, use: stainless steel sandwich pot, also known as steam pot sandwich, widely used in candy pharmaceutical, dairy wine, cakes, drinks, preserves, canned food processing, can also be used in large restaurants or canteen soup cook , stew, porridge and other food processing to improve quality, shorten time, improve the working conditions of good equipment. 2, Features: This pot to a certain pressure steam as the heat source, optional electric heating, heating area has heating evenly, the liquid boiling time is short, easy to control the heating temperature and so on. The pot pot layer (the inner pot) using acid resistant austenitic stainless steel manufacturing, with a pressure gauge and a safety valve, good looks, easy to install, easy to operate, safe and reliable. 3, the basic structure and installation of 1), the overall structure: fixed (vertical) main body and the leg by a pot composition; stirred fixed (vertical) Main body and legs pot, blender composition; tilting mainly by pot, tilting construction equipment composition; tilting the pot stirred mainly by the tilting device and a stirring device component; 2), tighten the support bracket of the two set screws, when cranking the pot, and both ends of the intake pipe the outlet pipe is not allowed to rotate with the pot. 3) installation of a stirred steamer, commissioning checks should be empty, until all rotating parts in normal operation, only put into use. 4), into steam, such as the joint leak may tighten the nut until no leakage so far. Electric heating sandwich pot use, characteristics, structural features, use and maintenance 1. Uses and Features: electric heating sandwich pot with high temperature resistance, corrosion resistance, strong production capacity, without steam heating, etc., are widely used in pharmaceutical, beverage, chemical, pigments, resins, research and other industrial sectors. 2. Features: electric heating sandwich pan from the pot, stirrer, heating jacket, bearing and gear shaft sealing devices and other components. Pot, blender, seal, electric heating means, such as by 1Cr18Ni9 (USU304) stainless steel. The lower part of the body has a discharge pot holes, sandwich pot stirrer. Welding brackets on the upper lid, equipment and motor reducer, drive shaft at the top of the lid from the pot stirrer, the shaft sealing device. Heating the jacket opened inlet, drain, vent valves, electric rods take over the holes. 3. Use and maintenance 1), the device is electrically heated sandwich pot, before class use, deal with various transmission parts inspection, lubrication, so dry grinding equipment damage. 2) Check the electrical wiring is in good condition, the connection is safe, secure, fuses match, everything is correct and complete only after the ohmic heating. 3) Check the HTF before starting amount, the amount of fuel to the fuel filler 8 cm or less. 4) during normal use, the upper edge of the pot two inlet not blocked in After refueling, open heating use. Electric heating power must be turned off after daily operation. 5), the operator at the time of the operation can not bring water to operate, when there is external oil leakage, stop the operation. 6), in the operation to strictly control the temperature, controlled at 200 degrees under normal circumstances. 7) When each oil change, should first electric tube removed, cleaned with lye and then refuel. 8), oil use 20 per pot, should oil change once every month should be finished using the oil discharge, so as not to affect the thermal effects. Join 40 ℃, 2% lye filled jacket soak 2 hours, then hot water clean, and then refuel. 9), every six months for maintenance, including: replacement of heating pipes, gaskets and electric pipe line ministries, check the thermometer and so on. 10), this electrical heating pot sandwich is a high-energy electrical equipment, in actual use, we must ensure the safe operation and management, the implementation of strict accordance with procedures, and make the daily operation records, in order to better maintain the equipment. 11), the use of sandwich pot against the material must be added to the solution, and then enter the material, agitator, and then turn on the electric power supply in order to reach the desired temperature of the process. In the material off before the electric power, over 2 to 3 minutes, then turn off the blender, after the end of the process, sandwich pot as soon as possible with warm water, brush with a slimy material, and then use the 0 ~ 50 ℃ alkaline thorough cleansing of the inner wall of the container, and rinse with water, no material under special pot (medium heat) either empty pot case not open the electric power supply, pay special attention to the use of temperature shall not exceed the fixed operating temperature 200 ℃. 12), sandwich pot should always pay attention to the work of the whole equipment and reducer, reducer lubricating oil shortage should be added immediately to the upper portion of the jacket and the lid of electric rods, electrical instrumentation, etc. should be checked regularly, if there is Failure to promptly replace or repair equipment when not in use, be sure to use warm water to thoroughly cleanse the inside and outside wall of the container, often scrub the pot to keep the look clean and bright interior, to achieve durable purpose.